PVC, TPR and silicone change the body, the tool and the file, and a material chart that ignores those three cannot choose between them. The useful question is which polymer suits the use in front of you: a bath duck that floats and squeaks, a hand-feel object for a desk, or a premium piece with a different report. The answer changes the mould, the additive question and the documents that travel with the goods.

PVC, TPR and silicone are three polymers rather than three grades of one thing.

What each polymer is: PVC is the familiar duck compound, softened with a plasticiser, which is why the additive question belongs to PVC alone. TPR is a thermoplastic rubber that softens with heat and sets on cooling, so it suits solid parts and a different tool. Silicone is a thermoset, held by a cured network rather than by a plasticiser, and it changes the tool, the print and the hand. In short, the material decides the tool and the file, not only the feel.

A close view of the moulded body of a yellow rubber duck

Three Polymers, Not Three Grades of One Thing

A duck body is a compound, not a material name. What arrives in a specification as PVC is a mixture: resin, plasticiser, stabiliser, pigment and process aids. What arrives as TPR is a thermoplastic rubber, usually a blend, that softens when heated and sets when cooled. What arrives as silicone is a thermoset that cures into a network and cannot be re-melted afterwards.

Those three sentences carry almost all of the practical difference. A thermoplastic can be re-melted, so the process looks like injection moulding and scrap can be reworked. A thermoset cures, so the process has to finish the part while the chemistry sets it. And a plasticised compound has an ingredient that can move, which is why the questions asked of it are different from the questions asked of a cured network.

This is the first thing to say in a brief: not which material is best, but what each one is. Once a buyer sees that two of the three are thermoplastics and one is a thermoset, the tool question and the print question usually answer themselves.

Four questions carry most of the decision, and they are worth answering before a sample is requested:

  • What does the duck have to do: squeak, float, sit on a desk, or be cleaned repeatedly?
  • Which polymer did the approved sample actually use, and was it sampled in that material?
  • Which colour lives in the compound and which sits on the surface, and who signs each proof?
  • What heat, water and handling will the duck meet after it leaves the carton?

It also explains why the safety conversation gets confused. The word PVC carries a compliance history that TPR and silicone do not share, and that history is about an additive rather than about the polymer itself. Separating the two is the whole point of the next section.

Sacks of raw material used in rubber duck production

The Additive Question Belongs to PVC

Flexible PVC is not flexible by itself. It is softened with a plasticiser, and that additive is the reason a PVC duck feels like a duck at all. It is also the reason PVC carries a specific set of questions that the other two do not, because an additive that can migrate is an additive that a child may reach.

That is a regulatory fact rather than a factory opinion: the plasticiser class is what the toy rules single out, and for PVC the question is which class is in the compound and whether the report names it. The phthalate and CPSIA note sets out what a report has to name for a PVC body.

For TPR and silicone the same question takes a different form. There is no plasticiser in the same sense, so the file turns to what the blend or the cured network contains, and to the pigments and process aids around it. That does not make either material automatically compliant with anything. It moves the question, it does not remove it.

The practical instruction is short: in a material brief, name the additive class, not just the polymer. A line that says PVC tells a factory almost nothing about what has to be declared.

The Tool Follows the Polymer

A duck body is made by a process, and the process follows from the polymer. A plasticised compound can be cast hollow in a rotating tool, which is how the classic squeeze duck gets a thin, flexible wall. A thermoplastic rubber flows in an injection tool and sets in the cavity under pressure, which suits solid parts and a tighter shape. A silicone body cures in or on a tool that has to work with the curing chemistry rather than with a melt.

Each route writes different lines onto the drawing. Casting cares about wall uniformity and where the filling hole is sealed. Injection cares about gate position, because the gate leaves a mark and that mark has to be somewhere the design can hide it. Cure based processes care about how the tool lets air and reaction products out, and about how the part is held while it sets.

The tool question is also a change question. A cast hollow body and an injection moulded body are not the same file with a different material line, so switching material partway through a program is a tool change as well as a compound change. That is the trap in the middle of a comparison: buyers compare materials as if the shape stays free, and it does not.

The rotocasting and injection comparison covers the two body routes in detail, and the shore hardness page covers what hardness does to the hand once the route is fixed.

A silicone mould cavity for a rubber duck body

The Hand Notices Two Things: Memory and Sound

Buyers describe material by feel, and two properties do most of that work: how the body comes back after a squeeze, and what it sounds like when it does. Memory is about how fast and how fully the wall returns. Sound is about how the wall and the air inside it react together.

A thin cast wall returns slowly and makes a soft, low sound. A thicker wall, or a solid part, returns immediately and makes a duller sound or none at all. That difference is not only the polymer. Wall thickness and the internal volume set the sound, which is why a stiff material can still produce a squeak and a soft one can be silent if the wall is wrong.

This is where a comparison of three materials stops being abstract. A silicone body that is designed solid has no air to move, so the sound question collapses into whether a squeaker part is fitted and how. A hollow cast body has the air built in, so the sound follows from the wall and the vent.

The useful instruction for a brief is to describe the reaction, not the material. A sentence such as "soft squeeze, slow return, audible squeak" tells a factory more than a material name, and it can be checked on a sample by squeezing it rather than by arguing about compounds.

Two yellow rubber ducks on a reflective black surface

Heat and Water Are Separate Tests

Two questions get merged in most material conversations and they should not be. Heat is a material question. Water is a construction question.

Heat exposes the difference between a thermoplastic and a thermoset. A thermoplastic softens as it warms, and a plasticised compound can also lose its additive over time under warm conditions. A cured network does not soften in the same way, which is one reason silicone appears in products that see heat. None of that makes one material suitable for an oven, and none of it should be read as a promise about a specific duck.

Water is about the body, not the polymer. A hollow duck floats because air is trapped inside, and it floats upright because the mass is arranged around that air. A solid duck floats only if the design gives it something to float with, and a small one may simply sink. The float balance page covers how that is designed, and the material choice sits underneath it rather than on top.

So the brief should ask two separate questions: what the duck will meet in use, and how the body is built. Answering the first with a material name and the second with a height is how a program ends up with a duck that is right in the hand and wrong in the water.

Two rubber ducks floating in a blue water tank

What Each Material Carries in Its File

Every material choice produces a document set, and the set is where two suppliers can look identical in a message and different in a file. The document has to name the compound, not the category, because a report that says PVC tells a buyer nothing about which plasticiser class, which pigment and which component were tested.

The standard side of the file is the same for all three when the duck is a children's toy, because the product that reaches the child is tested as a product rather than as a polymer.

The material side of the file is where the three diverge. A plasticised compound needs the additive declared. A blended thermoplastic needs the blend declared. A cured silicone needs the formulation and any post-cure processes declared, because the network is the product. In each case the useful question is the same: which compound, which colour, which component, and which report covers them.

The certificate verification page covers how a report is checked rather than assumed.

Material Is Not a Safety Grade

The most expensive misunderstanding in this comparison is the belief that the material is the safety grade. It is not. A cured silicone part can fail an edge requirement, a TPR part can fail a small parts test, and a PVC part can pass everything if the compound and the construction are right. The material sets which questions apply, not whether they are answered.

That is why a material swap in the middle of a program is more than a substitution. It changes the tool, the print method, the hand feel, the file and the tests, and it usually changes the sample that has to be approved again. A buyer who wants the same duck in a different material is asking for a different product that looks the same.

The honest position is easier to hold: choose the material for what the duck has to do, then build the file around what that material requires. A safety claim that starts with the material name is a slogan. A safety claim that names the compound, the test and the report is a file.

The Comparison to Put in a Brief

A brief does not need a verdict on the three materials. It needs four lines per material, so the choice can be argued against the use rather than against a preference.

QuestionPVC compoundTPRSilicone
What holds the shapeA plasticised compound, cast or mouldedA thermoplastic rubber that melts and setsA cured network that cannot be re-melted
What the tool looks likeA rotating cavity for a hollow body, or an injection toolAn injection tool with a gate the design has to hideA tool built around curing rather than melting
What the hand noticesSoft wall, slow return, air driven soundFirm return, tighter shape, duller soundDense feel, no plasticiser, sound depends on the part
What the file has to nameThe plasticiser class and the compoundThe blend and the compoundThe formulation and the cure

Read the table from the last row upwards. The file line is the one that decides whether a program can be signed, because it is the line that cannot be corrected after the tool is cut. The other three rows describe a product; the last row describes what can be proved about it.

Frequently Asked Questions

Is TPR better than PVC for a rubber duck?

Better is the wrong word, because the two are suited to different jobs. TPR suits firm solid parts and a tighter shape, and it does not raise the plasticiser question in the same form. PVC suits the soft hollow body that squeaks, and it brings an additive that has to be declared. The choice follows the use.

Can a silicone duck squeak?

A squeaker is a part, not a property of the polymer, so a silicone duck can carry one if the body is built to hold it and the wall reacts the right way. A solid silicone body has no air to move, so the sound has to come from a fitted part rather than from the body itself.

Which of the three is safest for children?

None of them is safe by name. Safety is a property of the finished product and the file behind it: the compound, the construction, the test and the report. A material name tells you which questions apply, not whether they were answered, and that is why the report has to name the compound.

Does the material change how a duck floats?

The construction decides float far more than the polymer does. A hollow body floats because of the air inside it, a solid body floats only if the design gives it buoyancy, and the mass has to be arranged for the duck to sit upright. Material changes the feel and the file; construction changes the waterline.

Final Note: Four Lines Before the Material Is Chosen

  1. Write what the duck has to do in the hand, in the water and in the file, before naming a material.
  2. Name the additive class for a PVC compound, because a polymer name declares nothing on its own.
  3. Treat a material change as a tool change and a new sample, not as a substitution in a note.
  4. Ask which compound, which colour and which component the report names, and check that the answer is a document rather than a sentence.

The three materials are close enough in appearance to make a comparison feel like a matter of taste, and different enough in tooling and paperwork to decide a program. The line that separates them is not which one feels best. It is which one a buyer can prove.

Key takeaways